一、在安装的时候配置网卡名称的参数
. 选择“Install Centos ”
. 按Tab，打开kernel启动选项后，增加 net.ifnames= biosdevname=
二、最小化安装完成之后必备安装软件
# 添加epel源，安装基础软件，设置主机名
rpm -ivh http://mirrors.aliyun.com/epel/epel-release-latest-7.noarch.rpm
yum install -y net-tools vim lrzsz tree screen lsof tcp wget tcpdump nc mtr nmap openssl-devel ntpdate
hostnamectl set-hostname linux-node1.example.com# 关闭firewalld和NetworkManager
systemctl stop firewalld
systemctl stop NetworkManager
systemctl disable firewalld
systemctl disable NetworkManager# 关闭selinux
setenforce 0
sed -i '/SELINUX/s/enforcing/disabled/' /etc/selinux/config# 设置打开文件描述符的数量
echo "* hard nofile 65536" >> /etc/security/limits.conf
echo "* soft nofile 65536" >> /etc/security/limits.conf# 设置记录历史命令的格式
echo 'export HISTTIMEFORMAT=" %F %T `whoami` "' >> /etc/profile
source /etc/profile# 使用tables键的时候补全systemctl命令
yum install -y bash-completion# 安装killall命令
yum install -y psmisc # 时间同步，如果没有内网时间同步可以使用公网的
crontab -e
*/5 * * * * /usr/sbin/ntpdate time1.aliyun.com
三、内核参数优化
cat /etc/sysctl.conf# 系统优化参数
# 关闭ipv6
net.ipv6.conf.all.disable_ipv6 =
net.ipv6.conf.default.disable_ipv6 = # 避免放大攻击
net.ipv4.icmp_echo_ignore_broadcasts = # 开启恶意icmp错误消息保护
net.ipv4.icmp_ignore_bogus_error_responses = # 关闭路由转发
net.ipv4.ip_forward =
net.ipv4.conf.all.send_redirects =
net.ipv4.conf.default.send_redirects = # 开启反向路径过滤
net.ipv4.conf.all.rp_filter =
net.ipv4.conf.default.rp_filter = # 处理无源路由的包
net.ipv4.conf.all.accept_source_route =
net.ipv4.conf.default.accept_source_route = #关闭sysrq功能
kernel.sysrq = # core文件名中添加pid作为扩展名
kernel.core_uses_pid = # 开启SYN洪水攻击保护
net.ipv4.tcp_syncookies = # 修改消息队列长度
kernel.msgmnb =
kernel.msgmax = # 设置最大内存共享段大小bytes
kernel.shmmax =
kernel.shmall = # timewait的数量，默认180000
net.ipv4.tcp_max_tw_buckets =
net.ipv4.tcp_sack =
net.ipv4.tcp_window_scaling =
net.ipv4.tcp_rmem =
net.ipv4.tcp_wmem =
net.core.wmem_default =
net.core.rmem_default =
net.core.rmem_max =
net.core.wmem_max = # 每个网络接口接收数据包的速率比内核处理这些包的速率快时，允许送到队列的数据包的最大数目
net.core.netdev_max_backlog = # 限制仅仅是为了防止简单的DoS 攻击
net.ipv4.tcp_max_orphans = # 未收到客户端确认信息的连接请求的最大值
net.ipv4.tcp_max_syn_backlog = 262144
# 启用timewait 快速回收，需要先打开时间戳。注：（NAT的网络和负载均衡器上不能打开）
net.ipv4.tcp_timestamps =
net.ipv4.tcp_tw_recycle = #开启重用。允许将TIME-WAIT sockets 重新用于新的TCP连接
net.ipv4.tcp_tw_reuse =
net.ipv4.tcp_mem =
net.ipv4.tcp_fin_timeout = # 当keepalive 起用的时候，TCP 发送keepalive 消息的频度。缺省是2小时
net.ipv4.tcp_keepalive_time = #允许系统打开的端口范围，不建议从1024开始，因为某些端口会存在10000以内。一般情况下已够用。
net.ipv4.ip_local_port_range = # 修改防火墙表大小，默认65536
net.netfilter.nf_conntrack_max=
net.netfilter.nf_conntrack_tcp_timeout_established=# 确保无人能修改路由表
net.ipv4.conf.all.accept_redirects =
net.ipv4.conf.default.accept_redirects =
net.ipv4.conf.all.secure_redirects =
net.ipv4.conf.default.secure_redirects =
Normal
0
7.8 磅
0
2
false
false
false
EN-US
ZH-CN
X-NONE
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:普通表格;
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-parent:””;
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.5pt;
mso-bidi-font-size:11.0pt;
font-family:”Calibri”,”sans-serif”;
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:”Times New Roman”;
mso-bidi-theme-font:minor-bidi;
mso-font-kerning:1.0pt;}
